Recent content by MrIdaho

  1. MrIdaho

    cleaning out garage

    YES I still have all the items. 1 "hot rod" golf cart with new motor and controller 2 motorized wheels (1-20 inch and 1-26 inch) 1 recumbent trike with 26 nch rear motorized rear wheel, dishk brakes on front. 1 20x20 recumbent trike with fairly new Bafange mid drive motor (yellow one in pics)...
  2. MrIdaho

    2 Golden Motor wheels for sale

    I have 2 motorized wheels with very little use for sale, One is a 20" wheel and the other is a 26" wheel. I have the controllers as well. $200 for each wheel
  3. MrIdaho

    cleaning out garage

    Due to health reasons I have to get rid of all my projects. Already got most of the parts gone but need to get rid of a recumbent trike w/20mm front hubs with disc brakes. Also my "hot Rod" needs to go bye bye. Anybody in Oregon or Washington give me a message if interested.
  4. MrIdaho

    hot rod golf cart

    still trying to get this dang thing running. Installed a new controller and still nothing going to contact the supplier of the motor/controller and hopefully that website that ed pedal car found? maybe get some answers
  5. MrIdaho

    hot rod golf cart

    I went over every connection and have yet to figure out WHY it does not run. I measured the throttle pedal voltage and come up with .853 and 2.936. Supposed to be 1- 4 volts I ordered a new controller and hopefully get it running. The battery still reads 53 volts. I was thinking the battery was...
  6. MrIdaho

    Ed's 'StreetRunner' Quad Build

    Been following this thread as I have same motor (only one). It was running last year before putting it in the garage. charged up battery and now it won't run? I recall you had similar issue? Keyswitch? hopefully it is something simple. In the wiring diagram sent w/ motor it shows BLACK WIRE is...
  7. MrIdaho

    Ed's 'StreetRunner' Quad Build

    took another look at your diagram. RED is aleays power, BLACK is ground
  8. MrIdaho

    Ed's 'StreetRunner' Quad Build

    suggest using an ohm meter with switch unconnected from anything. draw a schematic showing what happens when ?? this could/should show what each wire does internally.
  9. MrIdaho

    hot rod golf cart

    worked on the battery connections. Something isn't righ! it won't run. it did for about 2 seconds. my DMM needs a new battery then I might be able to track down bad connection. yes battery is charged.
  10. MrIdaho

    hot rod golf cart

    here is my schematic
  11. MrIdaho

    hot rod golf cart

    It finally got workable weather so back to work on my wifes "hot rod golf cart" Been designing a dashboard readout that displays SPEED, ODOMETER, BATTERY CONDITION and maybe outside temperature. here is a schematic that I need to edit but it has the basics. LIGHTED TACTIL SWITCHES FOR LIGHTS AND...
  12. MrIdaho

    trike w/ rear steering

    ran across this
  13. MrIdaho

    Ed's 'StreetRunner' Quad Build

    been pretty quite in Apply Valley. Maybe Ed got washed away with all the rain?
  14. MrIdaho

    Ed's 'StreetRunner' Quad Build

    been thinking about the forwaed/reverse switch. If you can measure the switch I can include a cutout for said switch. Measure using a caliper in milimeters. I would measure my switch but I have it mounted already. As for adjusting the PA volume, A volume control could be added or perhaps buy a...
  15. MrIdaho

    Ed's 'StreetRunner' Quad Build

    Forget the USB port as well. Tooo many things such as data to consider. If you wantjust a port for power then just a simple phono jack would do the deed. As for audio (am assuming for the sound effects of enging roaring? Just a simple amplifier and speakers
Top